Home> Blog> What is Busbar Bending Machine

What is Busbar Bending Machine

February 07, 2023

The Introduction of Busbar Bending Machine

The Automatic Busbar Bending Machine includes a bracket, a workbench and a clamping plate. The workbench of Automatic Busbar Bending Machine is placed on the bracket. The workbench is composed of a base and a pressure plate. The base is connected to the clamping plate through a hinge. The base is composed of a seat shell, a coil and a cover plate. The coil Placed in the depression of the seat shell, the top of the depression is covered with a cover plate. When in use, the wire is energized to the coil, and after energization, an attractive force is generated on the pressure plate, so as to realize the clamping of the thin plate between the pressure plate and the base. Due to the use of electromagnetic force clamping, the pressure plate can be made into a variety of workpiece requirements, and Automatic Busbar Bending Machine can also process workpieces with side walls.

Automatic Busbar Bending Machine

Lifting and installation of Hydraulic Busbar Bending Machine
1. The center of gravity of the Hydraulic Busbar Bending Machine is relatively high, and the front is heavy and the rear is light. Therefore, it is necessary to pay attention to the position of the center of gravity during lifting, handling and installation, so as to avoid machine overturning accidents. When lifting, the included angle of the lifting wire should be as small as possible. , so as to keep the accuracy of the machine tool unchanged.
2. The left and right columns of the Hydraulic Busbar Bending Machine are located on the working table as the benchmark for measuring the level, and the vertical and horizontal directions should be less than or equal to 1000:0.2. The foundation is prepared in advance according to the foundation map, and the hydraulic sheet metal bending machine is installed on the foundation At the same time, install the anchor bolts, and finally grout. After the cement is completely solidified, tighten the bolts and check the level.
Debugging of hydraulic bending machine pressure
1 The calculation pressure of the Hydraulic Busbar Bending Machine is calculated based on the tensile strength of the plate. If the properties of your boards are different, although the calculations are the same, the actual force required is naturally different.
2 If the external factors are the same, it is only the problem of the Hydraulic Busbar Bending Machine, which can be adjusted in two places, one is to adjust the tensile strength of the panel in the system, and the other is to adjust the DA value in the system settings.

Hydraulic Busbar Bending Machine

Instructions

1. First, turn on the power, turn on the key switch on the control panel, and then press the oil pump to start, so that you can hear the sound of the oil pump turning. (The machine does not work at this time)
2. Stroke adjustment, the use of the Aluminum Busbar Bending Machine must pay attention to the adjustment of the stroke, and it must be tested before bending. When the upper die of the bending machine goes down to the bottom, there must be a gap of plate thickness. Otherwise it will cause damage to the mold and machine. The stroke adjustment also has electric quick adjustment and manual fine adjustment.
3. For the selection of the bending notch, generally a notch with a width 8 times the thickness of the plate should be selected. If you bend a 4mm sheet, you need to choose a notch of about 32.
4. There are generally electric quick adjustments and manual fine adjustments for the adjustment of the back gauge, and the method is the same as that of the Shearing machine.
5. Step on the foot switch to start bending. Unlike the shearing machine, the Aluminum Busbar Bending Machine can be released at any time, and the Aluminum Busbar Bending Machine will stop when the foot is released, and continue to go down after stepping on it.

Contact Us

Author:

Mr. James

Phone/WhatsApp:

+86 13573186398

Popular Products
Industry News
Wire winding machine

July 29, 2019

You may also like
Related Information
The Hydraulic control form,Maintain and Design of Busbar Bending Machine

The Hydraulic control form,Maintain and Design of Busbar Bending Machine Hydraulic Control Form The hydraulic control system of the Professional Busbar Bending Machine is the central brain of the...

What are the main mechanisms of automatic winding machine?

What are the main mechanisms of automatic winding machine? The Wire Winding Machine For Good Quality is mainly composed of frame, winding spindle mechanism, wiring mechanism, winding fixture, tension...

The long-term growth trend of the industry remains unchanged

Since 2020, in order to alleviate the difficulties brought about by the epidemic on enterprises' production and operation, relevant state and local government departments have issued a number of...

Busbar Bending 3D Software

For each electric switchgear makers, the busbar bending is the most difficult process . Not only Angle control but also angle bending position control . Also the exact length of unfolded calculation...

Related Categories

Email to this supplier

Subject:
Email:
Message:

Your message must be betwwen 20-8000 characters

Contact Us

Author:

Mr. James

Phone/WhatsApp:

+86 13573186398

Popular Products
Industry News
Wire winding machine

July 29, 2019

Related Products List

Home

Product

Whatsapp

About Us

Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send